Assess a cotton pigment print for detail, handle and colour fastness, and send the right information for a roll-to-roll fabric printing quotation.

If you need digital pigment printing on cotton fabric by the metre, start with the actual production fabric. The same artwork can look and feel different on another ground colour or finish. Ünlü Group assesses digital pigment printing for each project through its fabric printing service in Bayrampaşa, Istanbul.
Include an unprinted area to see the ground, a solid colour area to assess handle and the finest lines of the design to check definition. Keep an untreated cutting from the same lot for comparison. Pretreatment, binder and fixing depend on the ink system and fabric. Epson’s guide describes pigment as an option for direct fabric printing.
For a cotton–polyester blend, give all fibre percentages and any details about coating or finishes. Compare your options with the cotton and polyester sample guide and evaluate the ground colour in person.
Fibre percentages help you choose a process, and the construction, ground colour and finish determine what you need to check on the sample. A closely woven cotton poplin and a stretchy cotton knit can have the same fibre content and feel quite different once a large area is printed. Give the print team the actual construction, fabric weight, roll width and details of any finish. If you are sending a cutting from a supplier, check the cutting and the fabric specification against the same article code.
Where several rolls or dye lots make up an order, identify the roll that supplies the cutting. Tell the printer about visible differences in shade or feel. Work out which differences require another sample based on the design and end use. If the fabric for production has yet to be purchased, note where the sample fabric differs from the intended ground. That makes it possible to review the right approval checks if the weight, shade or finish changes before production.
A repeat is the part of the design that tiles across the fabric. Specify its width and length in physical units alongside the file. To remove ambiguity, mark the planned size of a recognisable leaf, line or logo. Request a sample that shows at least one join between repeats. The join is where you can see whether a fine line steps, a motif gets cut off or a broad ground changes tone across the boundary. Check the join at the viewing distance that matters for the product.
If a detail must appear at a pocket, waistband or centre front, attach a placement drawing. Mark the crosswise and lengthwise directions and the areas cutting needs to preserve. Give the approval sample and the production artwork separate revision references. When a design is scaled or edited after a first test, label the new file and keep the approved swatch with the older reference. Cutting and quality teams can then check which physical repeat they are using against the drawing that was approved.
A small colour square can be useful for an initial colour discussion. For approval, include the largest solid area of the intended print, its smallest critical detail and an unprinted section on the same sample. Fold the solid area the way it will fold in a garment or finished article. Compare its handle with an unprinted cutting from the same lot and in the same grain direction. This gives you a more relevant comparison than two fabric swatches from different suppliers.
Include a section near the edge when the available print width controls the placement. Mark the boundary of the actual print and the area you expect to use for cutting. For knits, take the relaxed dimension first and, if the fabric will be stretched in use, look at the design at the intended stretch as well. Record the width and direction used for that check. If a full motif fits only across a particular width, include that dimension in the production specification and quote.
Look at the repeat at full size. Check fine edges, the join between repeats and uniformity in solid areas. View the sample under diffuse daylight and lighting similar to the product’s end use. Fold a solid printed area and the untreated cutting in the same way to compare their handle.
For fabric that will touch a pale lining or another textile, agree what colour transfer is acceptable. ISO 105-X12 addresses colour fastness to rubbing, and ISO 105-C06 addresses colour fastness to domestic and commercial laundering. Select relevant tests and acceptance criteria for the product.
Give the printer a physical reference where possible. The same ink colours can appear different on cream and white grounds or on surfaces with different sheen. View the sample and the reference in the same orientation and under the same light. When commenting on a photograph, point to the relevant patch and identify the face of the material. Take the final decision with the physical sample when the buyer needs an exact comparison.
Write down the priorities for the print. Two colours which are close on their own can read differently when they are adjacent or cover different parts of the design. Specify whether the ground, the main colour or a small borrowed detail is the point to change. Keep the physical card or approved swatch with its colour code and lighting notes. Use the same viewing conditions to judge a revised sample so that the difference visible in the cloth is easier to recognise.
Identify the materials that will come into contact with the printed area. Consider a pale lining, a bag strap against a shoulder, or a contrasting trim that will be pressed against the print. These parts of the garment can help you identify colours and surfaces to include in the test plan. Record the result for colour change in the print separately from any staining on a contact material. Use the same sample code when the physical swatch and a laboratory report go into different files.
Discuss the method, sample and conditions with the testing team. If dry and wet rubbing are required, identify each result in the request. For laundering, read the report alongside the planned care conditions and the procedure shown in the report. An agreed specification should identify the acceptance criteria the project uses. Keep the tested lot and colour area with the recorded result, particularly when the original design combines several bright and dark colours.
If a fine edge is heavier than expected, mark it on the image and give the production-scale size and artwork version. If a solid area feels heavy, point to that area and show which unprinted cutting was used for comparison. List the properties already approved and the one you need to revise. The printer can then compare the two swatches under the same conditions and check whether the difference comes from the design, the fabric or the way it was assessed.
A useful approval record lists the fabric code and lot, artwork version, dimensions of the repeat, face of the fabric and colour references. Give the new sample a different code from the first. If a colour changes after approval, return to the physical sample with its notes and decide which approval checks are relevant. Sharing decisions with the cutting and quality teams gives them a common reference when the first rolls arrive.
Send the fibres, construction, weight, ground colour, usable print width and order length, along with the artwork at physical repeat size. Include colour references, end use and the date you need an approved sample. Supply a cutting from the production lot if it is your fabric, or ask about fabric sourcing.
Tell the printer both the length available in the input rolls and the finished printed length you need. If you supply the fabric, list the number of rolls, metres per roll and lots. Explain the usable width the cutting plan needs and where matching or unprinted edges affect the yield. Two quotes can include the same gross metres and a different usable print width. Compare them against the same layout and finished quantity. Check how edge, sampling and recut allowances are treated.
For example, suppose two pieces across the width need 140 centimetres including their allowances. A quoted usable width of 145 centimetres can accommodate that row on paper. A width of 138 centimetres requires the cutting team to consider another layout. The cost per input metre alone may miss the effect of that change. Ask how the usable width was measured, then share it with the cutting team against the approved layout and grain direction.
Check whether fabric supply, preparation, sampling, series printing and fixing are included in the price. If one quote includes fabric and another assumes it is provided, compare those lines separately. Ask what the quote covers by colourway and file. Confirm when a sample will be ready for approval and whether the price assumes a particular order length or layout. Keep the quote revision and the sample code together.
Imagine an ecru cotton woven fabric for a shirt collection with a navy fine line and a large terracotta area. The request includes the weight, width, production repeat, the edge that has to stay sharp and a physical terracotta reference. An unprinted section from the same lot stays with the sample. Compare the solid area with that section for handle and check the printed sample after the intended care. The team can also measure the usable width along the boundary chosen for cutting.
Once the sample is accepted, purchasing quotes the same finished width and length. Quality records the approved swatch code, the fabric lot and the colours actually examined. Design marks the position to preserve on the cutting drawing. The first production print is checked under the same light and using the same measurement reference. This gives each team something it can compare when the production version is reviewed.
If the same artwork will run on several grounds, create a code for each ground and colour combination. A navy line on ecru and the same line on pale grey may use similar files and require separate colour decisions. Mark which rolls are allocated to each version. Compare the first delivery with the correct approval sample, using the same face and grain direction. If a difference appears, record where it was observed and which roll it came from before asking the printer to review it.
On the order confirmation, state which sample and quotation revision were used. Keep the initial requested width, the measured sample width and the accepted finished width in the same record. When the artwork or cloth changes after quotation, mark that change and tell the printer which earlier sample the request refers to. This helps purchasing link a revised price or date to the actual production change and helps the cutting team identify the dimensions to use on the marker for each order.
Compare like-for-like quotes and ask whether sampling, preparation, production printing and fixing are included. Send Ünlü Group your project details or compare related processes in the fabric printing methods guide.
phone: +90 212 576 5250
fax: +90 212 493 0336
email: info@unlutransfer.com
Yenidoğan Mah. Eser Sok. No: 6-8
Bayrampaşa, 34030,
Istanbul / Turkey
TR 9150171175
Bayrampaşa Tax Office