How to check bands and shade changes along a pigment-printed fabric roll

Map the position, direction and spacing of a mark. Check matching pattern repeats and unprinted cloth to guide the next inspection.

How to check bands and shade changes along a pigment-printed fabric roll

Start by locating the mark on the roll. Note how far it is from the end you opened, which edge it sits near and the direction it runs. If several marks look alike, measure the distances between them. Then compare the same point in other repeats of the design and check any unprinted cloth in line with the mark. This gives the printer enough information to find the right section. Direction and spacing help narrow the inspection. A confirmed explanation may also require the incoming fabric, the actual artwork and the record of the production stages.

Imagine you notice a lighter band across a broad ochre field. A few metres farther along, a second band catches your eye. One might cross most of the cloth, while the other stops near the middle. If the print has a clear margin, follow each mark to see whether it continues into the unprinted area. Check nearby sections where the same colour is present. A roll can show several kinds of mark. Give each finding its own position and description so the supplier can return to the right place.

Start from an end and an edge everyone can find

Record the roll identifier, lot, roll end and face you are looking at. Someone else may later open the roll from the opposite end. A distance from “the start” only works when the starting point is clear. Identify one selvedge as the reference across the width. For example, call it the left edge with the printed face up and the cloth unwinding away from you. Include that orientation in a sketch or in an overview photo. If the roll has already been cut, note where you started your measurement on the remaining material.

Describe the direction of the mark relative to the cloth. A thin line running along the roll and a band running across it require different coordinates. For a lengthwise line, write its distance from the reference edge and the length over which you can see it. For a crosswise band, note the distance along the roll and how much of the width it crosses. If a mark is diagonal or bends, record where it begins and where its direction changes. Take a view showing enough fabric to explain why you described it that way.

A broad shade change may have a gradual beginning and end. Note where it first becomes visible, where it looks strongest and where the shade seems to return to its usual appearance. Keep the surrounding cloth in view before you cut a sample. If you remove a piece, mark its direction and get a comparison from nearby. A local close-up can support a good description, but the overview is what identifies the section on the original roll.

Keep separate records for separate rolls. Several rolls can carry the same printed design while coming from different fabric or print lots. A lengthwise mark on one roll and a general shade change on another may need different inspections. List which lengths and widths have already been checked. If an end was cut off before inspection and its length is known, note that length alongside your measurements. Otherwise explain that you used the start of the remaining roll. This helps a supplier reconcile your locations with its production record.

Compare the mark with the repeat and the surrounding shade

Look at equivalent areas of the same colour in successive repeats. If a line only appears inside a specific part of the motif, check the artwork actually used for the run. The artwork may contain a pale shading detail or a change of tone at the repeat boundary. Two areas that look similar can have different colours by design. An exact comparison puts the same part of the repeat side by side. Confirm the revision of the file as well as the colourway, particularly when the same design was run several times.

If a mark crosses several different shapes along the same line, locate it relative to the edge of the cloth. For a streak that runs parallel to the edge, record where it begins and ends and whether it keeps the same distance across the width. For a set of transverse bands, pick the same point on each band when you measure the spacing. Note any variation, including a weaker or missing mark in the sequence. Several observations give the supplier more to compare than a single distance between two marks.

Suppose that pale bands appear at about four, six and eight metres from the start. These example positions show why it helps to check the motif as well as the tape. If a band falls across a circle, a second crosses an open area and a third falls in another colour, record all three positions. If every band follows the same boundary in the design, check the repeat layout and file first. A regular distance alone does not identify the machine part, process or cloth feature involved.

For a shade change across a larger area, compare the same print colour nearer the start and farther along the roll. Use comparable lighting and place the fabric in the same direction over a similar backing. A difference may first look like a band where the light falls across a fold. Check again with the fabric lying naturally. Write whether you see a sharp edge or a gradual transition. If the shift seems to affect one strip across the width more than the rest, identify which strip.

Use the approved physical sample if you have it. Compare a section that looks even with the approved shade and then place the marked section beside the same reference. Record a local band on the roll separately from a more general difference against the approved colour. The two can coexist. A good comparison uses the same motif and nominal colour on the same production ground wherever possible. If the reference differs in construction or size, say so when you describe the result.

Inspect the unprinted cloth at the same position

Follow the line to the edge of the printed area and check whether it continues into unprinted cloth. A raised yarn or slight change in texture can look more pronounced through a coloured area. Lay the cloth flat without pulling it. Try a side light to see whether the mark follows the yarns or changes as the cloth moves. Describe what is visible in each zone. “The raised line continues through the unprinted margin” is useful evidence without assigning a cause.

A fine raised line crossing the ochre printed area and the unprinted ground of the same woven sample

If the margin looks even, check whether the supplier has kept an unprinted piece from the same roll. Ask which end and width position it came from. A swatch cut from the start may tell you about the substrate generally, while a mark farther along may need an example closer to that location. If you have both incoming fabric and an unprinted piece taken after preparation, retain their separate identities. They document different conditions before printing. Under the same light, check whether a comparable change follows the same yarn direction on either piece.

A mark visible on unprinted cloth gives the team a reason to look at the ground and the preparation stages. A mark visible only in the print may prompt a review of the artwork, print process or later handling. Some variations can be much harder to see on bare cloth than through a broad solid print. Treat the print and unprinted observations as information for follow-up. If an unprinted reference is unavailable, record that limitation and compare the affected motif with a nearby repeat that looks even.

Send views that show where to look

Take an overview with a roll edge visible and a close view that shows the mark and the fabric immediately around it. Mark the coordinates on a plan or in the note that accompanies the image. If you photograph two pieces for a colour comparison, put them in one frame. A phone can use a different exposure for each separate shot. The picture may also make an outline look stronger if you used side lighting chiefly to reveal the surface. Say which image shows the normal view and which was taken to reveal texture.

An extended strip of ochre cloth and three small samples laid out beside different sections

Matching sections from the beginning, middle and end can help you assess a broader shade shift. If only one interval looks affected, compare an area within that interval with those just before and just after it. Choose check points that suit the length and intended use of the roll. Label any retained pieces with roll, position and direction. If you place samples from several rolls on one card, make the identity of each one visible. The card should be possible to interpret when it arrives without the inspector who prepared it.

If you saw two different patterns of variation, prepare two observations. A narrow line at a constant distance from the selvedge needs a view across the cloth and a note about how far it extends. A short crosswise band crossing more than one colour needs its length position and width coverage. Include whether either mark remains visible when viewed under usual inspection light. If a mark disappears in photographs, provide the location and the viewing conditions under which it was visible on the cloth.

Choose the next inspection from what you found

If a mark follows one part of the repeat, ask the printer to review that position in the production file and compare it on a different length of the roll. If it also crosses the unprinted margin, look for a corresponding surface feature in nearby cloth or in a retained sample. If the interval appears regular, give the supplier the individual positions so they can check them against the record of the run. Avoid collapsing several locations to one number if the variations differ in width or intensity.

When a mark becomes noticeable after finishing or storage, confirm that the earlier and later observations are from the same place. A photograph taken from another angle may have missed the effect the first time. Ask which operations were recorded for that section and when the fabric was next opened. If you request a second print, specify whether the aim is to reproduce the mark on the same lot or to check how a new lot behaves. Include an adjacent area of the same colour that looked even, where available.

Assess the marked zone against the cutting plan and the agreed inspection requirements. A band through a broad visible panel may matter differently from a mark within a seam allowance. If two parts will meet along a seam, place the intended pieces together in the cutting direction. A gradual change can go unnoticed in one piece and show up when a lighter section meets a darker one. Give the cutting team the affected length and width, along with the sample position and the pieces that should be matched.

Send the roll identifier, fabric lot, artwork revision and mark coordinates, plus the observation on the unprinted cloth. State whether you want the printer to check a general shade shift, a recurring band or a local surface change. When you review fabric printing options, include the approved physical reference and identify the affected portion of the roll in your sample or follow-up request.

Read more
Related articles
Use the Blog link to see all articles.
Contact Us
Contact

phone: +90 212 576 5250
fax: +90 212 493 0336
email: info@unlutransfer.com

Address

Yenidoğan Mah. Eser Sok. No: 6-8
Bayrampaşa, 34030,
Istanbul / Turkey

Business

TR 9150171175
Bayrampaşa Tax Office

WhatsApp