Choose where the pattern will sit on the pleat face, inside the fold and at the panel join. Check the first and last folds on the same sample.

Decide what should show on each part of the fold before laying out the pattern. Mark one complete repeat on the open cloth. Then relate that repeat to the visible face, the part that turns underneath and the point where two panels join. If you want the same stripe in the same place on each face, find the corresponding point in the repeat for every fold. If you want to retain the full sequence of colours, read several closed faces together. Finally, align the panels at their stitching lines. Two pieces that look regular on their own can form a narrow pair of stripes or cut a motif in half at the join.
Take navy cloth with fine ecru stripes and a narrower copper stripe. The brief could ask for one ecru stripe near the same edge of each face, with the copper stripe revealed only when the wearer takes a step. Another brief could use the same cloth and ask for the original sequence of ecru and copper on the visible faces. The two layouts place their folds at different points in the repeat. Show the sample room which stripe should remain visible at rest and which should appear in motion. A swatch folded both ways explains the placement more clearly than a request to match the stripes.
Lay the cloth face up and identify the direction of the design. For lengthwise stripes, read the repeat across the stripes. For a motif that repeats both across the cloth and down its length, mark both directions. An asymmetric colour sequence might leave a short gap on one side of a copper stripe and a long gap on the other. Start at a recognisable edge and find the next point where the same order of colours begins. Take the repeat between those two corresponding edges. The nearest stripe of the same colour may belong to a different part of the sequence.
Check how the design lies relative to the grain. A printed stripe and a woven stripe both need to be observed on the actual cloth. Follow one stripe from the top of the planned panel to the bottom and compare it with the grainline. A pleat laid along the grain can cross a stripe that drifts across it. Rotating the pattern to catch the first stripe may affect how the panel hangs and how the next piece fits alongside it. Show both directions on the sample notes if they appear to differ. Review the full panel before changing the cutting direction.
For directional flowers, arrows or leaves, also mark which way is up. Two panels can meet at the same stripe while a motif on one piece points the opposite way. Use one mark for the grainline and another for the top of the motif. If centre front should always sit next to a distinctive stripe, link that decision to the finished garment line. Record the start of the repeat on each piece. A measurement taken only from the selvedge may fail to locate the same band if the pattern sits in a different place on the next length of fabric.
Mark the future fold edge, the visible face and the part that will turn underneath on an open sample. Keep a copy of the marks on a drawing or on an edge where they can be found again. Close one pleat and see where the selected stripe lands. Fold several more to check that its position repeats. A stripe close to the edge of a face can disappear partially underneath if the crease moves. Specify whether the ecru should sit at the edge, run through the centre or sit at a measurable distance from a particular side. Record the edge of the stripe used for that measurement.

Open one pleat gently to simulate the movement the garment is meant to allow. If the copper stays underneath at rest, observe how much of it becomes visible as the fold opens. Use the same support at the top if the panel will be held under a waistband. A strong pull can expose a part of the cloth that will never appear in ordinary use. Photograph the same fold closed and partly open from the same side. Mark the fold on both views. This gives the workshop a physical reference for where the second colour belongs and when it should show.
If the brief calls for the full sequence of stripes to remain on show, examine several faces at once. Read across them at a shared height. Look for a complete band on one face being replaced with a half band on the next. A photograph from above can show a change that is easy to miss when inspecting the pleats one by one. Relate those faces back to the open repeat and mark the start and end of the visible pieces. Compare the sequence with the approved design. If only ecru belongs on the outside, use the same check to locate the hidden copper on several folds.
Imagine that the original stripe repeat is 6 cm. If a fold starts at the selected ecru stripe and the next start is 12 cm away on the open cloth, it lands two full repeats later. It therefore meets the same point in the colour sequence. If the fold starts are 13 cm apart, each step moves one extra centimetre through the sequence. Over several folds this changes the part of the stripe that lands on the visible face. These figures illustrate a straight, regular layout. Measure both the repeat and the open spacing in the fabric and fold arrangement you plan to use.
Moving the first fold changes where the series begins. It does not change how the later folds progress through the design if the spacing stays the same. If the first fold reads well and the third and fourth look progressively different, track the open positions of those later folds. Consider whether a different repeat in the fabric or a different fold spacing is possible. Changing spacing can affect the finished size, so check the new option on a sample before approving it. If the fold spacing is fixed, the brief may have to specify a different arrangement of the stripes.
Also follow one stripe down the length of a folded sample. A stripe that sits in the right place at the top can move towards the edge lower down. Compare its position at the top, middle and hem while keeping the cloth relaxed. A constant sideways offset calls for a review of the starting point. A growing difference calls for a check of the line of the fold, the direction of the stripe and how the cloth lay on the table. Mark the affected area before adjusting the pattern. The smallest trial that shows the difference should include the full length over which it appears.
Mark the stitching lines of both pieces before checking the join. Bring those lines together and look at where the last visible stripe on one piece sits relative to the first on the other. The raw edges include allowances that will turn inside. For lengthwise stripes, compare the gap around the seam with the spacing between the other visible stripes. For crosswise stripes, check that the same band meets the seam at the same height on each piece. If the fabric has an obvious top and bottom, verify that the adjoining motifs point in the intended directions.

A pair of stripes that is closer together at the seam can draw the eye to that position. If the narrow pair was intended, record it as a design decision. For a continuous rhythm, compare the first and last fold positions with the stitching lines. Shifting a seam can change the finished panel width. Review the dimensions as well as the appearance before approving that adjustment. Baste the pieces, then inspect them flat and supported as they will be on the garment. Check what happens if the join is in a valley that remains covered at rest but opens during movement.
For crosswise stripes, choose one band near the top and another lower down. If the upper bands meet and the lower bands miss, compare the spacing of both pieces before moving the first match point. Fabric direction, cutting layout and the way the join is held can affect the comparison. Fold the allowances into their intended position and inspect the face. A band that appears to make contact on the open table can show an interruption once the seam allowance turns inside. Photograph the basted seam before taking it apart and keep a view of the reverse side if it shows how the bands were placed.
Walk both pattern pieces across the cloth at full scale. Match centre front or the first pleat to the chosen motif on each piece. Turning the second piece to save cloth may reverse an arrow or leaf. A design that calls for a mirror image may also require the two fold directions to oppose each other. Check what that does to the parts that show when the pleats open. If the fit and motif direction require a particular placement, mark it and see whether the next panel can start at the same point in the repeat within the usable cloth width.
Record the extra distance needed to find a matching start on the next piece. A consistent start on the first panel does not guarantee enough room for all the others in the same direction. Before cutting, mark all the start points and show which ones will remain available after the first panels are cut. If a trial needs adjustment only around the seam, keep the fold depth and motif direction constant while testing that change. Once a short basted trial gives the desired result at the join, apply the same placement to a full panel and check it at the intended support points.
Send an open cloth view, a front view with the folds closed and a close view of the basted join. Mark the beginning of the fabric repeat on the open view, the repeated stripe on the closed faces and the stitching line on the join. Show where the first and last folds start, which face of the cloth is visible and which way the motif points. If a stripe should appear in movement, keep the open and closed views of the same fold. Note whether dimensions refer to the centre of a stripe or to one edge, especially where narrow bands sit side by side.
When the fabric or the pattern scale changes, measure the repeat again and lay the original fold positions over the new cloth. When the fold spacing changes, check how the stripe arrangement continues across the seam. Keep a small open strip alongside the approved folded sample so the next person can compare both states. A complete approval covers the rhythm on the visible faces, what appears when the cloth moves and the way the design continues at the panel join.
phone: +90 212 576 5250
fax: +90 212 493 0336
email: info@unlutransfer.com
Yenidoğan Mah. Eser Sok. No: 6-8
Bayrampaşa, 34030,
Istanbul / Turkey
TR 9150171175
Bayrampaşa Tax Office